Weather-guard 1225 Bedienungsanleitung PDF herunterladen

Part No. 24-0135 REV. D ECN 5315 05/13

ASSEMBLY AND INSTALLATION INSTRUCTIONS

Model 1225 Service Body Ladder Rack

WARNING

This product is only intended for, and only safe for, transporting ladders,

lumber, pipe and other similar materials. It is the responsibility of the

user to secure these materials to the rack before transporting. Any

modifications made to this product, or use of this product for any other

purpose than its intended use, will create a hazardous condition that will

cause serious personal injury or property damage.

IMPORTANT

BEFORE YOU BEGIN

Read these instructions and

warnings completely before

installing.

BOLT KIT

Bolt Kit #32-0110 is provided with

your ladder rack. Check this bolt kit

to be sure the following parts are

included:

Quan. Description

5 3/8-16 x 3/4" Hex Head,

Thread Cutting

24 3/8-16 x 1-1/2" Carriage

Bolt

4 3/8-16 x 1-1/4 Carriage Bolt

28 3/8" Flat Washer

28 3/8-16 Nylon Lock Nut

4 5/16-18 x 2" Carriage Bolt

8 5/16-18 x 1" Carriage Bolt

12 5/16 Flat Washer

12 5/16-18 Nylon Lock Nut

2 5/16" x 2-3/4" Snapper Pin

4 Rope Cleat (black)

8 10-24 x 2-3/4" F.H. Screw

8 10-24 Nylon Lock Nut

2 Square Cap Plug (black)

* See Bolt Chart on back page for

fastener reference

TOOLS REQUIRED

 Electric Drill

 Drill Bits - 7/32", 3/8", 7/16" & 1/2

 3/8 Open or Box End Wrench

 1/2" Open or Box End Wrench (2)

 9/16" Open or Box End Wrench (2)

 Screwdriver - common

 Framing Square

 Pencil or Marker

 Tape Measure

 Hack Saw

 Hammer

CAUTION

Never load your rack to exceed the safe rated capacity of your vehicle.

Heavy loads carried high can dangerously alter the center of gravity.

MAXIMUM

LOAD CAPACITY

1000 lbs.

(evenly distributed)

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - WARNING

Part No. 24-0135 REV. D ECN 5315 05/13ASSEMBLY AND INSTALLATION INSTRUCTIONSModel 1225 Service Body Ladder Rack WARNINGThis product is only inten

Seite 2

NOTE: To prevent rust from occur-ring, touch-up any drilled holes.NOTE: Apply E-6000 Sealant* to theservice body around drilled holesprior to assembly

Seite 3 - CAUTION

31.Rear Leg Support Installation - Begin with the rear of the vehicle, asthe taillight location may determine the mounting option as well as the side

Seite 4

4Figure 8. Assembled Leg Support - used for marking all rear mounting holesOption 1 Installation - Place a Lower Bracket at the top of the rear endpan

Seite 5

53.Leg Height - Measure from inside Leg Support to a minimum of at least 2above cab of truck (see Figure 11.). The Legs can be cut this dimension. NO

Seite 6

3/8-16 x 1-1/4Carriage Bolt(2 places)3/8 FlatWasher(2 places)3/8-16 NylonLock Nut(2 places)Cushion Strip(cut from bulk)6. Rail Fastening - Bolt the

Seite 7 - Thread Cutting

8. Rear Crossmember - Place the Crossmember in the sockets, center it,then mark the socket holes. Remove the Crossmember and drill the marks with a3/8

Seite 8 - WARNING

- NOTICE -Any modification or unintended use of this product shall immediately void all manufacturers warranties.Manufacturer disclaims all liability